SIO.SYS and VSIO.SYS open beta.

                                  Copyright, 1992 By
                                   Raymond L. Gwinn
                                 12469 Cavalier Drive
                              Woodbridge, Virginia 22192

          USE THIS SOFTWARE AT YOUR OWN RISK.

          SIO.SYS and  VSIO.SYS are functional, but  not exact, replacement
          for OS2's COM.SYS and VCOM.SYS.  Documentation, beyond that given
          here,  is not available.   There is currently  no Windows support
          (ie no compatible COMM.DRV).

          General Distribution  of  SIO/VSIO  is  currently  restricted  to
          CompuServe and Bob Juge's BBS at 713-980-9671.

          A  supporting  FidoNet  echomail  conference  called SIO_BETA  is
          available from Bob Juge at 1:106/2000.

          Messages/reports   from   program   authors   will   be   greatly
          appreciated.    Messages may  be  sent directly  to  the SIO/VSIO
          author via CompuServe, 72570,157 (Ray  Gwinn).  Messages may also
          be  sent via FidoNet netmail, using host routing, to 1:265/104 or
          directly  to 1:265/104  from  3:00am  to  6:00am EST  (8:00am  to
          11:00am UTC).

          SIO.SYS and VSIO.SYS are  intended to be high  performance Serial
          Input/Output routines.   Some brain  dead software  may not  work
          with  these routines.  Also, some perfectly good software may not
          work with these routines.  In any case, if you have programs that
          do  not  work with  SIO/VSIO installed  let  me know  and, PLEASE
          CONTACT THE AUTHOR of that software also.  Ask them to get a copy
          of SIO/VSIO and report any errors they find.  It is not practical
          for  me to set  up and test all  communications programs that are
          being used by OS2 users.

          It is intended  that SIO.SYS  will accept the  same command  line
          parameters that COM.SYS uses.  Unlike VCOM.SYS, VSIO.SYS requires
          no  command   line  parameters.    VSIO   obtains  all  necessary
          information from SIO.SYS.

          If you are using a serial mouse, the mouse device  driver must be
          loaded before SIO/VSIO.

                                NOTICE  NOTICE  NOTICE
          OS2 seems to  have a bad habit of thinking  com programs are IDLE
          when they are  not.  It is  critical for good operation  of a com
          program that the DOS settings of  IDLE SENSITIVITY be set to  100
          and IDLE_SECONDS be set to 15 or more.







          Some (but not all) differences between COM.SYS and SIO.SYS are:

          1 - SIO.SYS  insists upon  using 16550A (or  up) fifos.   SIO.SYS
          does not allow application programs to disable the fifos.

          2 - SIO.SYS will accept any number above 50 as a baud rate.

          3 -  The last decimal  digit of a  given baud rate  must be zero.
          For example, 50, 110, and 115200 are valid while 75 and 134.5 are
          not.  A baud rate  of 75 will be rounded to 80 and  134.5 will be
          rounded to 130.

          4  - SIO.SYS  is considerably  faster than  COM.SYS.   Any timing
          dependant software (intentional or unintentional) may croak.

          5 - Half duplex has not been tested and probably does not work.

          Some (but not all) differences between VCOM.SYS and VSIO.SYS are:

          1  - VSIO.SYS  creates  a virtual  16550A  instead of  a  virtual
          8250/16450.

          2 - VSIO.SYS does not virtualize the loopback mode of the 16550A.

          2  - VSIO.SYS is considerably faster than VCOM.SYS.  Well written
          DOS  programs  can  achieve  throughput far  in  excess  if  1000
          characters per second.

          Sample CONFIG.SYS statements:

          DEVICE=C:\SIO.SYS (1,3F8,4) (COM2:19200,2F8,IRQ3)
          DEVICE=C:\VSIO.SYS